Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Florence-Graham, CA
Gate installation in Florence-Graham usually means replacing a gate that was custom-built for a driveway barely wider than the car itself. These are 1920s and 1930s bungalows on narrow lots, and most original gates have been welded, shimmed, and re-hinged so many times that at some point repair stops making sense. We handle that transition honestly: we’ll tell you when a gate can be saved and when it’s time for a new one. Gate Repair South Gate has served Florence-Graham since 2013, and most of what we install here is measured to the inch because nothing is standard. Call (833) 620-0289 if your gate is dragging, won’t latch, or never worked right.
Why Florence-Graham Homes Are Different
Florence-Graham’s housing stock runs compact: stucco bungalows and duplexes built between the 1920s and 1940s, set on lots where the driveway is often only a foot or two wider than the car. That’s the defining fact of gate work here. The original single-car drives are so tight that nearly every gate is custom-fit, sometimes to within an inch of the fence post. When a gate sags even slightly, it drags on the concrete and stops latching. Our techs keep shim stock and hinge-repair plates on the truck for almost every Florence-Graham call because alignment is the usual problem, not rust.
The weather shapes the failures too. Dry, warm Los Angeles Basin conditions mean wood dries and warps while metal corrodes slowly at the hinges and latch, not through the body. Sun-baked wood gates pull away from their frames; steel gates settle until the latch no longer lines up. It’s less about catastrophic rust-outs and more about slow drift, which is why small adjustments fix a surprising number of Florence-Graham gates without a full replacement. The homes are close together as well, so a gate that won’t close is visible from the street and leaves the whole side yard and parked cars exposed. That’s why most of our work here is urgent security repair, not cosmetic upgrades.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Florence-Graham Services
Two services get called out most in Florence-Graham: mechanical gate repair and electric gate repair. Here’s what each one actually involves in this neighborhood.
Gate Repair in Florence-Graham
Most mechanical gate failures in Florence-Graham are alignment problems. A wheel or hinge wears enough that the gate drops, drags on the driveway, and refuses to latch. We fix wheel carriers, hinge posts, sagging frames, latch misalignment, and bent or seized hardware on the original metal and wood gates found all over the 90001 ZIP. Because the lots are narrow and the gates are tightly fitted, the repair is usually a matter of lifting, shimming, and re-securing rather than replacing the whole panel. See Gate Repair in Florence-Graham for the full breakdown of what we do and what it costs.
Electric Gate Repair in Florence-Graham
Automatic gates here are often retrofits: an older manual gate that got a motor added years later. That means wiring was run through tight side yards, and the operator works harder than it should against a gate that was never perfectly balanced. We troubleshoot the motor, control board, safety sensors, and keypad as one system, because replacing a motor on a gate that still won’t latch solves nothing. Most of what we work on in Florence-Graham includes Mighty Mule and Ghost Controls on residential driveways, plus DoorKing on a few of the multi-unit properties. Read Electric Gate Repair in Florence-Graham for signs, costs, and turnaround.
Gate Installation in Florence-Graham
New gate installation in Florence-Graham is not a “pick a size off the shelf” kind of job. The driveways on these 1920s-40s bungalows are so narrow that most gates are measured, welded, or cut to fit a specific opening, and a gate that’s off by an inch will scrape its entire swing. On top of that, the dry basin heat means untreated wood will warp within a couple of years, so material choice matters. A proper Florence-Graham install means measuring the opening, checking the posts, building or ordering the gate to fit, and setting hinges so the gate stays square for years, not months. For the full install scope, visit our Gate Installation page.
Automatic Gate Installation
Signs you need it
You want your existing gate to open and close on a motor instead of by hand, or your current automatic system is too far gone to justify another repair.
What it costs in Florence-Graham
Automatic gate installation in Florence-Graham typically runs between $2,500 and $6,500, with the final number depending on whether we’re motorizing an existing gate or installing a new gate and operator together.
How we do it
We measure the gate and post spacing, confirm the operator’s duty rating matches the gate’s weight, check the power source, install the motor and brackets, set travel limits, wire in the safety edges and photocells, and program remotes and the keypad.
Driveway Gate Installation
Signs you need it
Your current driveway gate is sagging, rusted through, or so patched with previous repairs that it no longer swings cleanly or latches at all.
What it costs in Florence-Graham
A new driveway gate in Florence-Graham typically ranges from $1,800 to $4,500 for a single swing gate, with materials and the custom fitting to a narrow drive driving most of the variance.
How we do it
We measure the existing opening, choose a material that will hold up to the dry sun, fabricate or order the gate to fit, set or sleeve the hinge posts, hang the gate, and dial in the latch and stops so it clears the concrete and closes securely.
Sliding Gate Installation
Signs you need it
Your driveway slopes or is so short that a swing gate would hit the car or the house, or you want a gate that doesn’t need inward clearance at all.
What it costs in Florence-Graham
Sliding gate installation in Florence-Graham typically falls between $3,500 and $7,500, because it requires a longer track, a motor with a rack and pinion drive, and often a concrete footer for the track in these tight side yard spaces.
How we do it
We pour or anchor the track system, hang the sliding panel on rollers, install the operator and rack, set the open and close limits, and wire the safety features before adjusting the gate so it rolls without binding.
What Gate Installation Costs in Florence-Graham
| Item | Typical range in Florence-Graham |
|---|---|
| Manual driveway gate (single swing) | $1,800 – $4,500 |
| Sliding gate with operator | $3,500 – $7,500 |
| Automatic system (gate and motor) | $2,500 – $6,500 |
How long does a gate installation take in Florence-Graham?
Most standard driveway gate installations take one to two days. Custom-fabricated gates for narrow Florence-Graham openings may add a few days for the gate to be built, but the on-site work is usually the shorter part.
Do you handle the concrete work for gate posts in Florence-Graham?
Yes, if the existing posts are cracked or leaning we remove them, dig new footers, and set new posts. Most Florence-Graham yards have old posts that look fine until the gate comes off and you see the rot or corrosion underneath.
Brands We Service in Florence-Graham
We work on LiftMaster, DoorKing, Elite, and Mighty Mule systems across Florence-Graham, plus the other major automation brands. Because gates are our entire trade, we carry common parts for these brands locally, which shortens turnaround when a control board or sensor has failed. See our brands for the full list of what we service.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Florence-Graham, CA
| Service | Typical range in Florence-Graham |
|---|---|
| Manual driveway gate (single swing) | $1,800 – $4,500 |
| Sliding gate with operator | $3,500 – $7,500 |
| Automatic system (gate and motor) | $2,500 – $6,500 |
| Gate wheel or hinge repair | $150 – $400 |
| Gate post repair or reset | $300 – $750 |
| Gate opener motor replacement | $500 – $1,100 |
| Control board replacement | $350 – $800 |
| Remote or keypad programming | $100 – $250 |
Two things push gate prices up in Florence-Graham. The first is the narrow lot: nearly every gate has to be custom fit, and that means more labor and less room to work. The second is recurring alignment damage, where a gate that has dragged for years bends the hinge post or tears the wheel mount. On every job, the price is quoted and agreed before any work begins, so you know the number before a tool comes off the truck.
Neighborhoods We Serve in Florence-Graham
We work throughout the 90001 ZIP and the surrounding blocks. Most of our calls come from the residential streets south of Florence Avenue and around the older bungalow rows near Compton Avenue and Central Avenue.
- Florence-Graham residential core
- Streets south of Florence Avenue
- Around Compton Avenue
- Near Central Avenue
- Eastern side of the 90001 ZIP
For most repair calls in Florence-Graham, we can be on site quickly, often the same day depending on the time of the call and our schedule.
Service Area – Cities Near Florence-Graham
Gate Repair South Gate also covers the surrounding South Los Angeles area. We handle gate repair and installation in Watts, CA, Central-Alameda, CA, Vermont Vista, CA, and South Gate, CA. If you’re a few blocks outside the Florence-Graham line, call (833) 620-0289 to confirm coverage.
Serving Florence-Graham, CA – Our Local Coverage Area
We’re based in the Florence-Graham area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Florence-Graham
Most standard driveway gate replacements in Florence-Graham don’t need a permit, since they’re replacing an existing gate on the same posts. If the job involves a new electrical run for an automatic operator, or new posts and footers, a permit can be required. We’ll flag that before work starts and can guide you on the filing process.
In most cases, yes. Because Florence-Graham is inside our primary service area and our trucks are stocked with common hinge, wheel, and latch parts for these older gates, we can often schedule a repair the same day you call. Automatic and electric gate issues sometimes take a diagnostic visit first so we can confirm the failed part before returning with the right board or sensor.
Yes, and that’s a large share of our Florence-Graham work. The original metal and wood gates on these homes are often worth keeping if the posts are still solid. We’ll tell you plainly when a gate can be repaired and when continued welding and shimming would cost more than a new custom-fit replacement.
If your gate in Florence-Graham is sagging, stuck, or dead, call (833) 620-0289. We’ll give you a straight answer on whether it’s a repair or a replacement, and a free estimate either way.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Florence-Graham Customers Say
"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Rachel Mercer"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
- Nicole Anderson"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Wade Quinn